+===================== Installing FreeBSD ==========================+ | | | Table of Contents: | | | | 0.0 Quick Start: | | 0.1 Installing FreeBSD from CDROM or the Internet. | | | | 1.0 Detail on various installation types: | | 1.1 Installing from a network CDROM | | 1.2 Installing from Floppies | | 1.3 Installing from a DOS partition | | 1.4 Installing from QIC/SCSI tape | | 1.5 Installing over a network using NFS or FTP | | 1.5.1 NFS Installation tips | | 1.5.2 FTP Installation tips | | 1.6 Tips for Serial Console Users | | | | 2.0 DOS User's Q&A section. | | 2.1 How do I make space for FreeBSD? | | 2.2 Can I use compressed DOS filesystems from FreeBSD? | | 2.3 Can I use DOS extended partitions? | | 2.4 Can I run DOS executables under FreeBSD? | | | +=====================================================================+ Author: Jordan K. Hubbard Last updated: Tue May 4 16:05:41 PST 1999 0.0 Quick Start --- ----------- This manual documents the process of making a new installation of FreeBSD on your machine. If you are upgrading from a previous release of FreeBSD, please see the file UPGRADE.TXT for important information on upgrading. If you are not familiar with configuring PC hardware for FreeBSD, you should also read the HARDWARE.TXT file - it contains important information which may save you a lot of grief. If you're new to FreeBSD then you should also read EVERYTHING listed in the Documentation menu of the installer. It may seem like a lot to read, but the time you spend now reading the documents will be made up many times over because you were adequately prepared. Also, you will know the types of information available should you get stuck later. Once the system is installed, you can also revisit this menu and use a WEB browser to read the installed FAQ (Frequently Asked Questions) and Handbook HTML documentation sets for FreeBSD. You can also use the browser to visit other WEB sites on the net (like http://www.freebsd.org) if you have an Internet connection. See ABOUT.TXT for more information on the resources available to you. The best laid plans sometimes go awry, so if you run into trouble take a look at TROUBLE.TXT which contains valuable troubleshooting information. You should also read ERRATA.TXT before installing and follow the pointers there carefully since this will stop you from falling over any problems which have reported in the interim for your particular release. DISCLAIMER: While FreeBSD does its best to safeguard against accidental loss of data, it's still more than possible to WIPE OUT YOUR ENTIRE DISK with this installation if you make a mistake! Please do not proceed to the final FreeBSD installation menu unless you've adequately backed up any important data first! We really mean it! FreeBSD requires a 386 or better processor to run (sorry, there is no support for '286 processors) and at least 5 megs of RAM to install and 4 megs of RAM to run. You will need at least 100MB of free hard drive space for the most minimal installation. See below for ways of shrinking existing DOS partitions in order to install FreeBSD. 0.1 Installing FreeBSD from CDROM or the Internet --- --------------------------------------------- The easiest type of installation is from CD. If you have a supported CDROM drive and a FreeBSD installation CD from Walnut Creek CDROM, there are 2 ways of starting the installation from it: 1. If your system supports bootable CDROM media (usually an option which can be selectively enabled in the controller's setup menu or in the PC BIOS for some systems) and you have it enabled, FreeBSD supports the "El Torrito" bootable CD standard. Simply put the installation CD in your CDROM drive and boot the system to begin installation. 2. Build a set of FreeBSD boot floppies from the floppies/ directory in every FreeBSD distribution. Either simply use the ``makeflp.bat'' script from DOS or read floppies/README.TXT for more information on creating the bootable floppies under different operating systems. Then you simply boot from the first floppy and you should soon be in the FreeBSD installation. If you don't have a CDROM and would like to simply install over the net using PPP, slip or a dedicated connection, simply fetch the /floppies/boot.flp file from: ftp://ftp.freebsd.org/pub/FreeBSD or one of its many mirrors (http://www.freebsd.org/handbook/mirrors.html) and follow step 3 above. You should also read the floppies/README.TXT file as it contains important information for downloaders. Once you have your boot floppies made, please go to section 1.5 of this document for additional tips on installing via FTP or NFS. 1.0 Detail on various installation types --- ------------------------------------ Once you've gotten yourself to the initial installation screen somehow, you should be able to follow the various menu prompts and go from there. If you've never used the FreeBSD installation before, you are also encouraged to read some of the documentation in the the Documentation submenu as well as the general "Usage" instructions on the first menu. NOTE: If you get stuck at a screen, hit the F1 key for online documentation relevant to that specific section. If you've never installed FreeBSD before, or even if you have, the "Standard" installation mode is the most recommended since it makes sure that you'll visit all the various important checklist items along the way. If you're much more comfortable with the FreeBSD installation process and know _exactly_ what you want to do, use the Express or Custom installation options. If you're upgrading an existing system, use the Upgrade option. The FreeBSD installer supports the direct use of floppy, DOS, tape, CDROM, FTP, NFS and UFS partitions as installation media, further tips on installing from each type of media listed below. 1.1 Installing from a network CDROM --- ------------------------------- If you simply wish to install from a local CDROM drive then see the Quick Start section. If you don't have a CDROM drive on your system and wish to use a FreeBSD distribution CD in the CDROM drive of another system to which you have network connectivity, there are also several ways of going about it: 1. If you would be able to FTP install FreeBSD directly from the CDROM drive in some FreeBSD machine, it's quite easy: You simply add the following line to the password file (using the vipw command): ftp:*:99:99::0:0:FTP:/cdrom:/sbin/nologin And anyone else on your network will now be able to choose a Media type of FTP and type in: ``ftp://'' after picking "URL" in the ftp sites menu. 2. If you would rather use NFS to export the CDROM directly to the machine(s) you'll be installing from, you need to first add an entry to the /etc/exports file (on the machine with the CDROM drive) which looks something like this: /cdrom -ro ziggy.foo.com To allow the machine "ziggy.foo.com" to mount the CDROM directly via NFS during installation. The machine with the CDROM must also be configured as an NFS server, of course, and if you're not sure how to do that then an NFS installation is probably not the best choice for you unless you're willing to read up on rc.conf(5) and configure things appropriately. Assuming that this part goes smoothly, you should be able to enter: cdrom-host:/cdrom as the path for an NFS installation when the target machine is installed, e.g. wiggy:/cdrom 1.2 Installing from Floppies --- ------------------------ If you must install from floppy disks, either due to unsupported hardware or just because you enjoy doing things the hard way, you must first prepare some floppies for the install. First, make your boot floppies as described in floppies/README.TXT Second, read the file LAYOUT.TXT and pay special attention to the "Distribution format" section since it describes which files you're going to need to put onto floppy and which you can safely skip. Next you will need, at minimum, as many 1.44MB floppies as it takes to hold all files in the bin (binary distribution) directory. If you're preparing these floppies under DOS, then THESE floppies *must* be formatted using the MS-DOS FORMAT command. If you're using Windows, use the Windows File Manager format command. Don't trust Factory Preformatted floppies! Format them again yourself, just to make sure. Many problems reported by our users in the past have resulted from the use of improperly formatted media, which is why I'm taking such special care to mention it here! If you're creating the floppies from another FreeBSD machine, a format is still not a bad idea though you don't need to put a DOS filesystem on each floppy. You can use the `disklabel' and `newfs' commands to put a UFS filesystem on a floppy, as the following sequence of commands illustrates: fdformat -f 1440 fd0.1440 disklabel -w -r fd0.1440 floppy3 newfs -t 2 -u 18 -l 1 -i 65536 /dev/rfd0 After you've formatted the floppies for DOS or UFS, you'll need to copy the files onto them. The distribution files are split into chunks conveniently sized so that 5 of them will fit on a conventional 1.44MB floppy. Go through all your floppies, packing as many files as will fit on each one, until you've got all the distributions you want packed up in this fashion. Each distribution should go into its own subdirectory on the floppy, e.g.: a:\bin\bin.inf, a:\bin\bin.aa, a:\bin\bin.ab, ... IMPORTANT NOTE: The bin.inf file also needs to go on the first floppy of the bin set since it is read by the installation program in order to figure out how many additional pieces to look for when fetching and concatenating the distribution. When putting distributions onto floppies, the .inf file MUST occupy the first floppy of each distribution set! This is also covered in ABOUT.TXT Once you come to the Media screen of the install, select "Floppy" and you'll be prompted for the rest. 1.3 Installing from a DOS partition --- ------------------------------- To prepare for installation from an MS-DOS partition you should simply copy the files from the distribution into a directory called "FREEBSD" on the Primary DOS partition ("Drive C:"). For example, to do a minimal installation of FreeBSD from DOS using files copied from the CDROM, you might do something like this: C:\> MD C:\FREEBSD C:\> XCOPY /S E:\BIN C:\FREEBSD\BIN Assuming that `E:' was where your CD was mounted. For as many `DISTS' as you wish to install from DOS (and you have free space for), install each one in a directory under `C:\FREEBSD' - the BIN dist is only the minimal requirement. Once you've copied the directories, you can simply launch the installation from floppies as normal and select "DOS" as your media type when the time comes. 1.4 Installing from QIC/SCSI Tape --- ----------------------------- When installing from tape, the installation program expects the files to be simply tar'ed onto it, so after fetching all of the files for the distributions you're interested in, simply tar them onto the tape with a command something like this: cd /where/you/have/your/dists tar cvf /dev/rwt0 (or /dev/rsa0) dist1 .. dist2 When you go to do the installation, you should also make sure that you leave enough room in some temporary directory (which you'll be allowed to choose) to accommodate the FULL contents of the tape you've created. Due to the non-random access nature of tapes, this method of installation requires quite a bit of temporary storage! You should expect to require as much temporary storage as you have stuff written on tape. SPECIAL NOTE: When going to do the installation, the tape must be in the drive *before* booting from the boot floppies. The installation "probe" may otherwise fail to find it. Now create a boot floppy as described in section 0.1 and proceed with the installation. 1.5 Installing over a network using FTP or NFS --- ------------------------------------------ After making the boot floppies as described in the first section, you can load the rest of the installation over a network using one of 3 types of connections: Serial port: SLIP / PPP Parallel port: PLIP (using ``laplink'' style cable) Ethernet: A standard Ethernet controller (including certain PCCARD devices). Serial Port ----------- SLIP support is rather primitive, and is limited primarily to hard-wired links, such as a serial cable running between two computers. The link must be hard-wired because the SLIP installation doesn't currently offer a dialing capability. If you need to dial out with a modem or otherwise dialog with the link before connecting to it, then I recommend that the PPP utility be used instead. If you're using PPP, make sure that you have your Internet Service Provider's IP address and DNS information handy as you'll need to know it fairly early in the installation process. You may also need to know your own IP address, though PPP supports dynamic address negotiation and may be able to pick up this information directly from your ISP if they support it. You will also need to know how to use the various "AT commands" for dialing out with your particular brand of modem as the PPP dialer provides only a very simple terminal emulator. Parallel Port ------------- If a hard-wired connection to another FreeBSD or Linux machine is available, you might also consider installing over a "laplink" style parallel port cable. The data rate over the parallel port is much higher than what is typically possible over a serial line (up to 50k/sec), thus resulting in a quicker installation. It's not typically necessary to use "real" IP addresses when using a point-to-point parallel cable in this way and you can generally just use RFC 1918 style addresses for the ends of the link (e.g. 10.0.0.1, 10.0.0.2, etc). IMPORTANT NOTE: If you use a Linux machine rather than a FreeBSD machine as your PLIP peer, you will also have to specify "link0" in the TCP/IP setup screen's ``extra options for ifconfig'' field in order to be compatible with Linux's slightly different PLIP protocol. Ethernet -------- FreeBSD supports most common PC Ethernet cards, a table of supported cards (and their required settings) being provided as part of the FreeBSD Hardware Guide (see the Documentation menu on the boot floppy or the top level directory of the CDROM). If you are using one of the supported PCMCIA Ethernet cards, also be sure that it's plugged in _before_ the laptop is powered on! FreeBSD does not, unfortunately, currently support "hot insertion" of PCMCIA cards during installation. You will also need to know your IP address on the network, the "netmask" value for your address class and the name of your machine. Your system administrator can tell you which values are appropriate to your particular network setup. If you will be referring to other hosts by name rather than IP address, you'll also need a name server and possibly the address of a gateway (if you're using PPP, it's your provider's IP address) to use in talking to it. If you do not know the answers to these questions then you should really probably talk to your system administrator _first_ before trying this type of installation! Using a randomly chosen IP address or netmask on a live network will almost certainly get you shot at dawn. Once you have a network connection of some sort working, the installation can continue over NFS or FTP. 1.5.1 NFS installation tips ----- --------------------- NFS installation is fairly straight-forward: Simply copy the FreeBSD distribution files you want onto a server somewhere and then point the NFS media selection at it. If this server supports only "privileged port" access (as is generally the default for Sun and Linux workstations), you will need to set this option in the Options menu before installation can proceed. If you have a poor quality Ethernet card which suffers from very slow transfer rates, you may also wish to toggle the appropriate Options flag. In order for NFS installation to work, the server must also support "subdir mounts", e.g. if your FreeBSD distribution directory lives on: wiggy:/usr/archive/stuff/FreeBSD Then wiggy will have to allow the direct mounting of /usr/archive/stuff/FreeBSD, not just /usr or /usr/archive/stuff. In FreeBSD's /etc/exports file this is controlled by the ``-alldirs'' option. Other NFS servers may have different conventions. If you are getting `Permission Denied' messages from the server then it's likely that you don't have this properly enabled! 1.5.2 FTP Installation tips ----- --------------------- FTP installation may be done from any mirror site containing a reasonably up-to-date version of FreeBSD. A full menu of reasonable choices for almost any location in the world is provided in the FTP site menu during installation. If you are installing from some other FTP site not listed in this menu, or you are having troubles getting your name server configured properly, you can also specify your own URL by selecting the ``URL'' choice in that menu. A URL can contain a hostname or an IP address, so the following would work in the absence of a name server: ftp://192.216.191.11/pub/FreeBSD There are two FTP installation modes you can use: o FTP: For all FTP transfers, use the standard "Active" mode for transfers. This will not work through most firewalls but will often work best with older ftp servers that do not support passive mode. If your connection hangs with passive mode, try this one! o FTP Passive: For all FTP transfers, use "Passive" mode. This allows the user to pass through firewalls that do not allow incoming connections on random port addresses. NOTE: ACTIVE AND PASSIVE MODES ARE NOT THE SAME AS A `PROXY' CONNECTIONS, WHERE A PROXY FTP SERVER IS LISTENING ON A DIFFERENT PORT! In such instances, you should specify the URL as something like: ftp://foo.bar.com:1234/pub/FreeBSD Where "1234" is the port number of the proxy ftp server. 1.6 Tips for Serial Console Users --- ----------------------------- If you'd like to install FreeBSD on a machine using just a serial port (e.g. you don't have or wish to use a VGA card), please follow these steps. 1. Connect some sort of ANSI (vt100) compatible terminal or terminal emulation program to the COM1 port of the PC you are installing FreeBSD onto. 2. Unplug the keyboard (yes, that's correct!) and then try to boot from floppy or the installation CDROM, depending on the type of installation media you have, with the keyboard unplugged. 3. If you don't get any output on your serial console, plug the keyboard in again and wait for some beeps. If you are booting from the CDROM, proceed to Step 5 as soon as you hear the beep. 4. For a floppy boot, the first beep means to remove the kern.flp floppy and insert the mfsroot.flp floppy, after which you should press enter and wait for another beep. 5. Hit the space bar, then enter boot -h and you should now definitely be seeing everything on the serial port. If that still doesn't work, check your serial cabling as well as the settings on your terminal emulation program or actual terminal device. It should be set for 9600 baud, 8 bits, no parity. 2.0 DOS user's Question and Answer section --- -------------------------------------- 2.1 Help! I have no space! Do I need to delete everything first? --- -------------------------------------------------------------- If your machine is already running DOS and has little or no free space available for FreeBSD's installation, all is not lost! You may find the "FIPS" utility, provided in the tools/ subdirectory on the FreeBSD CDROM or on the various FreeBSD ftp sites, to be quite useful. FIPS allows you to split an existing DOS partition into two pieces, preserving the original partition and allowing you to install onto the second free piece. You first "defrag" your DOS partition, using the DOS 6.xx "DEFRAG" utility or the Norton Disk tools, then run FIPS. It will prompt you for the rest of the information it needs. Afterwards, you can reboot and install FreeBSD on the new partition. Also note that FIPS will create the second partition as a "clone" of the first, so you'll actually see that you now have two DOS Primary partitions where you formerly had one. Don't be alarmed! You can simply delete the extra DOS Primary partition (making sure it's the right one by examining its size! :) NOTE: FIPS does NOT currently work with FAT32 or VFAT style partitions as used by newer versions of Windows 95. To split up such a partition, you will need a commercial product such as Partition Magic 3.0. Sorry, but this is just the breaks if you've got a Windows partition hogging your whole disk and you don't want to reinstall from scratch. 2.2 Can I use compressed DOS filesystems from FreeBSD? --- -------------------------------------------------- No. If you are using a utility such as Stacker(tm) or DoubleSpace(tm), FreeBSD will only be able to use whatever portion of the filesystem you leave uncompressed. The rest of the filesystem will show up as one large file (the stacked/dblspaced file!). DO NOT REMOVE THAT FILE as you will probably regret it greatly! It is probably better to create another uncompressed DOS extended partition and use this for communications between DOS and FreeBSD if such is your desire. 2.3 Can I mount my DOS extended partitions? --- --------------------------------------- Yes. DOS extended partitions are mapped in at the end of the other ``slices'' in FreeBSD, e.g. your D: drive might be /dev/da0s5, your E: drive /dev/da0s6, and so on. This example assumes, of course, that your extended partition is on SCSI drive 0. For IDE drives, substitute ``wd'' for ``da'' appropriately. You otherwise mount extended partitions exactly like you would mount any other DOS drive, e.g.: mount -t msdos /dev/da0s5 /dos_d 2.4 Can I run DOS binaries under FreeBSD? --- ------------------------------------- Ongoing work with BSDI's doscmd utility is bringing this much closer to being a reality in FreeBSD 3.0, though it still has some rough edges. If you're interested in working on this, please send mail to emulation@FreeBSD.org and indicate that you're interested in joining this ongoing effort! There is also a neat utility called "pcemu" in the ports collection which emulates an 8088 and enough BIOS services to run DOS text mode applications. It requires the X Window System (XFree86) to operate. ---- End of Installation Guide ---